图片
2014年7月22日星期二
MASTER plastic rattan garden furniture and master meter box application
Master plastic rattan garden furniture and master meter box: in the distribution boxinstallation requirements of elastic line position, concealed in disk assembly,distribution box should be installed in the safety box, electric drying, convenient operation. Plastic pallets mold master plastic rattan garden furniture and master thebottom meter box board, is generally 1.5 meters, 1.2 meters away from the bottommounting at, photo gallery installed electric meter board at the end of the mouth is not less than 1.8 meters, in the same building, MASTER electrical meter box of similar disc height theelectric meter box, the allowable deviation of 10mm. Installation of wooden master electrical meter boxes needed and iron until shall be embedded hanging typedistribution box (disc) should be used for gold in the expansion bolt. Plastic palletsmold and mastering electric meter box need to brush paint, then brush the dust paint,two. Master the floor tile mould and master all kinds of iron electric meter boxembedded shall be brushed with antirust paint, and do the obvious and reliablegrounding. Wire panel, electric meter box panel line hole shall be smooth without burrs, metal should be installed insulation protection sleeve. Master the electric meter box implement with iron plate, MASTER plastic rattan garden furniture and metal shell surface and with the appliance door andelectric appliances, PE ground protection shall be clear and reliable, PE line was yellow and green color line also can use braided flexible bare copper wire, but the PEground protection does not allow the use of box or the box body is connected in series. Plastic pallets mold and MASTER floor tile mold electric meter box panel wiringare arranged in rows, and bound into bundles, electric meter box in the active siteshould be fixed. The lead wire isocyanide introduction should leave the appropriateredundancy, to facilitate maintenance. Master conductor exploitation at the electric meter box should not hurt the core or core line is too long, master mold traverse tilehead should be solid and reliable. The electric meter box multi strand conductor shall not coil crimping, except should install a crimping terminal crimping hole with. If mustperforation with screw crimping should rinse tin pressure connection, and shall not reduce the number of strands.
MASTER plastic rattan garden furniture and master the plastic pallets mold difference
Master of
plastic pallets mold is a professional production of high strength blow
molding trays, plastic trays, plastic tray.MASTER plastic rattan garden furniture Plastic
pallets mold master fromsummarizing other tray production enterprise
experience, grasp the plastic pallets mold adopts international
advanced mold design custom injection molding software design and
development of plastic pallets mold, plastic barrelthan master mold
and other manufacturers developed plastic tray MASTER plastic pallet mould
with mechanical structure, channel distribution and appearance the
overall structure of the tray appearance
style, more scientific,reasonable, master mold products plastic
tray tray bearing capacity, grasp theplastic bucket mould strong impact
resistance, good temperature resistance.MASTER plastic buckets mold
and master the plastic
pallets mold double-sided,single-sided, custom custom injection
molding injection molding plain word at the end of nine feet, a
custom injection molding, custom injection
moldingplane, grid, mesh, master mold, plastic barrel custom injection
molding, Tian word series tray and bottom plate is widely used
in: petroleum chemical industry, beer, beverage, food and
medicine, tobacco feed, clothing electronic,warehousing logistics, MASTER plastic rattan garden furniture port
terminals and other production, transportation,storage and circulation
field.
What is the role of UPS backup power supply?
Chinese plastic injection molding and MASTER plastic rattan garden furniture application
China
plastic injection molding and MASTER plastic rattan garden furniture:
runner and gate at
the
parting
line, and products
in the
mold with demolding, the most simple design,
easy processing,
low cost,MASTER plastic rattan garden furniture so more people to use flood system operation. Plastic mold structure is divided into two parts: the fixed die and the moving
die. With the
active injection
machine part
is movable
mould, injection molding
machine
injection in
the end do not generally called the fixed mould. Because the fixed mould part of large nozzle mold generally formed by two pieces of steel is also known as
"the structure
of the mold two
plate mold".
Two plate mold structure is the most simple edge gate.
Or
a constant
temperature hot
runner plate and
heat pump mouth, no
cold material
release, runner and gate on the products
directly,MASTER plastic rattan garden furniture so the channel does not need to release, this system is also known as the no water inlet system, which can save raw materials, suitable for raw materials, products more expensive higher requirements, design and processing difficulties high cost,MASTER plastic rattan garden furniture mould.China plastic injection molding hot runner system,
also known as hot
runner
system, China plastic injection molding is mainly composed of
a hot
runner
sleeve, hot runner plate, temperature control electric box. Our common hot runner system has a single point and multi-point hot runner hot runner in two forms.
MASTER china plastic injection molding: runner and gate is not in the parting line, directly on the product,MASTER china plastic injection molding so to design a set of nozzle parting line, MASTER plastic rattan garden furniture design is more
complex, processing more
difficult, usually depending on the product requirements and selection of fine nozzle system. The fixed mould part small inlet die is formed by three pieces of
steel is also known as "the structure of the die mould".
Three plate mold structure is small inlet die the most simple.
Or
a constant
temperature hot
runner plate and
heat pump mouth, no
cold material
release, runner and gate on the products
directly,MASTER plastic rattan garden furniture so the channel does not need to release, this system is also known as the no water inlet system, which can save raw materials, suitable for raw materials, products more expensive higher requirements, design and processing difficulties high cost,MASTER plastic rattan garden furniture mould.China plastic injection molding hot runner system,
also known as hot
runner
system, China plastic injection molding is mainly composed of
a hot
runner
sleeve, hot runner plate, temperature control electric box. Our common hot runner system has a single point and multi-point hot runner hot runner in two forms.Master plastic mould factory and MASTER plastic rattan garden furniture relationship
Master plastic mould factory and MASTER plastic rattan garden furniture: mould plastic box, can be repeatedly used after carefulcleaning. In need of special attention, some microwave lunch box, the box body is with 5 PP production, master plastic mould factory the lid is to 1, PE manufacturing,because PE can not withstand high temperatures, it is not with the box body be put inmicrowave oven. For insurance purposes,MASTER plastic rattan garden furniture the container in the microwave, put the lidoff. Master mold plastic mold factory use: heat and cold, but can not be put into themicrowave oven, so as to avoid high temperature and release chemicals. Master moldplastic mold factory and cannot be used by strong acid, strong alkali charge, and becauseit will dissolve the polystyrene, easy to cause cancer. Therefore, you should try toavoid packaged snack foods hot. MASTER plastic molding factory use: a widely usedmaterial, especially used in baby bottles containing bisphenol , because of thecontroversial. In theory, as long as in the process of making PC, bisphenol A 100%into plastic Structure, he said the products completely no bisphenol , MASTER plastic pallet mould if there is no small amount of bisphenol Ainto plastic structure of PC, may be released into the food or drink. Plastic palletsmoldmaster used to be careful, grasp the plastic mold factory mold in the use of this plasticcontainers should be extra attention. Master of bisphenol A residual plastic palletsmold, the higher the temperature, the more the faster speed of release.
订阅：
博文 (Atom)